Mitsubishi Outlander: Cruise control
Cruise control is an automatic speed control system that lets you keep the same driving speed. It can be activated at 40 km/h (25 mph) or more.
CAUTION:
● When you do not wish to drive at a constant speed, deactivate the cruise control function for safety.
● Do not use cruise control when driving conditions will not allow you to stay at the same speed, such as in heavy traffic or on roads that are winding, icy, snowy, wet, slippery or on a steep downhill slope.
● If you shift to “N” (Neutral) in cruise control mode without pressing the clutch first, the engine will run too fast and might be damaged.
NOTE:
● Cruise control may not be able to keep your speed on uphills or downhills.
Cruise control switches
A- “ON OFF” switch
Used to activate and deactivate the cruise control function.
B- “COAST SET” switch
Used to reduce the set speed and to set the speed of constantspeed driving.
C- “ACC RES” switch
Used to increase the set speed and, when constant-speed driving is finished, to return to the original set speed.
D- “CANCEL” switch
Used to terminate constant-speed driving.
NOTE:
● When operating the cruise control switches, correctly press each cruise control switch.
The cruise control may be turned off automatically if two or more of the cruise control switches are pressed at the same time.
“CRUISE” control indicator
This indicator will come on when the cruise control “ON OFF” switch (A) is pressed to turn on the cruise control system.
To activate
1. Lightly press the “ON OFF” switch (A).
NOTE:
● If the cruise control is on when the ignition switch is turned to “OFF” position, cruise control will turn on automatically and the “CRUISE” control indicator will illuminate the next time you start the engine.
● If the battery voltage is insufficient, the memory data for the cruise control will be erased. As a result, the “CRUISE” control indicator may not come on when you restart the engine. If this happens, press the “ON OFF” switch once again to activate the cruise control.
2. Press the “COAST SET” switch (B) while driving at the desired speed.
NOTE:
● The speed when you released the “COAST SET” switch will be set as the cruising speed.
● It is not possible to set the vehicle speed while driving in 1st gear.
To increase the set speed
There are 2 ways to increase the set speed.
“ACC RES” switch If you press and hold down the “ACC RES” switch (C), the speed will gradually increase. When you reach your desired speed, release the switch. Your cruising speed is now set.
To increase the speed in small amounts, press the “ACC RES” switch (C) for less than 1 second and release it. Every time you press the “ACC RES” switch (C), the speed will increase by approximately 1.6 km/h (1 mph).
Accelerator pedal
Use the accelerator pedal to reach your desired speed and then push the “COAST SET” switch (B) and release the switch momentarily to set a new desired cruising speed.
To decrease the set speed
There are 2 ways to reduce the set speed.
“COAST SET” switch Press and hold the “COAST SET” switch (B) while driving at the set speed, and you will slow down (coast) gradually.
When you reach desired speed, release the “COAST SET” switch. Your cruising speed is now set.
To decrease the speed in small amounts, press the “COAST SET” switch (B) for less than 1 second and release it. Every time you press the “COAST SET” switch (B), the speed will decrease by approximately 1.6 km/h (1 mph).
Brake pedal
Use the brake pedal, which disengages the cruise control, then push the “COAST SET” switch (B) and release the switch momentarily to set a new desired cruising speed.
To temporarily increase or decrease the speed
To temporarily increase the speed
Press the accelerator pedal as you would normally. When you release the pedal, you will return to your set speed.
To temporarily decrease the speed
Apply the brakes to decrease the speed. To return to the previously set speed, press the “ACC RES” switch. Refer to “To resume the set speed”.
To deactivate
The cruise control can be turned off as follows:
● Press the “ON OFF” switch (A) (cruise control function will be deactivated).
● Press the “CANCEL” switch (D).
● Depress the brake pedal or slightly tap it.
The cruise control can be turned off automatically in any of the following ways:
● By pressing the clutch pedal down.
● When your speed slows to about 35 km/h (22 mph) or less.
● When the active stability control (ASC) starts operating (if so equipped). Refer to “Active stability control (ASC)”.
To resume the set speed
If the cruise control is deactivated by the condition described in “To deactivate”, you can resume the previously set speed by pressing the “ACC RES” switch (C) while driving at a speed of approximately 40 km/h (25 mph) or greater.
Under either of the following conditions, however, using the switch does not allow you to resume the previously set speed.
In these situations, repeat the speed setting procedure:
● The cruise control is turned OFF.
● The ignition switch is turned to the “OFF” position.
READ NEXT:
Reversing sensor system
This system operates when you are backing the vehicle. It uses corner and back
sensors to detect an obstacle and sounds a buzzer to inform you of the approximate
distance to the obstacle.
CAUTION
Cargo loads
Cargo loads precautions
CAUTION:
● Do not load cargo or luggage higher than the top of the seatback. Be sure that
your cargo or luggage cannot move once your vehicle is moving. Having the re
Trailer towing
In order to tow a trailer with your vehicle, have a trailer towing device that
meets all relevant regulations in your area, mounted at an authorised MITSUBISHI
dealer.
The regulations concerning
SEE MORE:
Emergency starting
If the engine cannot be started because the battery is weak or dead, the battery
from another vehicle can be used with jumper cables to start the engine.
WARNING:
● To start the engine using jumper cables connected to another vehicle, perform
the correct procedures according to the instr
Hands-free Bluetooth® cellular phoneinterface system with voice recognition
The Hands-free Bluetooth® cellular phone interface system with voice recognition
uses a wireless communication technology known as Bluetooth® to allow you to make
hands-free calls in your vehicle using your Bluetooth® compatible cellular phone
with Hands-free profile.
The system is equippe
