Mitsubishi Outlander: Front seat
To adjust forward or backward
Manual type
Pull the seat adjusting lever and adjust the seat forward or backward to the desired position, and release the adjusting lever.
WARNING:
● To ensure the seat is locked securely, try to move the seat forward or backward without using the adjusting lever.
Power type
Adjust the seat by operating the switch as indicated by the arrows.
1- Adjustment forward.
2- Adjustment backward.
NOTE:
● To prevent the battery from discharging, use the power seat while the engine is on.
To recline the seatback
Manual type
In order to recline the seatback, lean forward slightly, pull the seatback lock lever up, and then lean backward to the desired position and release the lever. The seatback will lock in that position.
CAUTION:
● The reclining mechanism of the seatback is spring loaded, causing it to return to the vertical position when the lock lever is operated. When using the lever, sit close to the seatback or hold it with your hand to control its return motion.
Power type
Adjust the seatback angle by operating the switch as indicated by the arrows.
1- To move to forward direction.
2- To recline rearward.
NOTE:
● To prevent the battery from discharging, use the power seat while the engine is on.
To adjust seat height (driver’s seat only)
Manual type
To adjust the seat height, operate the lever repeatedly to adjust.
1- Raise.
2- Lower.
Power type
To adjust the seat height, operate the switch as indicated by arrows.
NOTE:
● To prevent the battery from discharging, use the power seat while the engine is on.
1- To move the front of the seat up and down
2- To move the rear of the seat up and down
3- To move the whole seat up and down
Armrest
The lid of the floor console box can be moved forward and backward, and used as an armrest.
Heated seats
The heated seats can be operated with the ignition switch in the “ON” position. The indication lamp (A) will illuminate while the heater is on.
1- Heater high (for quick heating).
2- Heater off.
3- Heater low (to keep the seat warm).
CAUTION:
● Operate in the high position for quick heating. Once the seat is warm, set the heater to low to keep it warm. Slight variations in seat temperature may be felt while using the heated seats. This is caused by the operation of the heater’s internal thermostat and does not indicate a malfunction.
● If the following types of persons use the heated seats, they might become too hot or receive minor burns (red skin, heat blisters, etc.):
• Children, elderly or ill people • People with sensitive skin • Excessively tired people • People under the influence of alcohol or sleep inducing medication (cold medicine, etc.) ● Do not place heavy objects on the seat or stick pins, needles, or other pointed objects into it.
● Do not use a blanket, cushion, or other material with high heat insulation properties on the seat while using the heater; this might cause the heater element to overheat.
● Do not use benzene, petrol, alcohol or other organic solvents when cleaning the seats. Doing so could damage not only the seat cover, but also the heater element.
● If water or any other liquid is spilled on the seat, allow it to dry thoroughly before attempting to use the heater.
● Turn the heater off immediately if it appears to be malfunctioning during use.
READ NEXT:
Second seat
When a person is sitting in the second seat, raise the head restraints to height
at which it lock in position. Refer to “Head restraints”.
NOTE:
● It is possible to adjust each side of t
Third seat (7 persons)
To fold out the underfloor-stowable third seat
The third seat is stowed under the floor. Use the seat when extra people ride
in your vehicle. When not in use, stow the seat under the floor and use
Head restraints
WARNING:
● Driving without the head restraints in place can cause you and your passengers
serious injury or death in an accident. To reduce the risk of injury in an accident,
always make su
SEE MORE:
Inspection Procedure
Inspection Procedure 1: Scan tool cannot communicate with WCM.
CAUTION
Before replacing the ECU, ensure that the communication
circuit is normal.
TECHNICAL DESCRIPTION (COMMENT)
If the scan tool cannot communicate with the WCM,
the CAN bus lines may be defective. If the WCM
does not work, the WCM or
Reversing sensor system
This system operates when you are backing the vehicle. It uses corner and back
sensors to detect an obstacle and sounds a buzzer to inform you of the approximate
distance to the obstacle.
CAUTION:
● The reversing sensor system assists you in determining the approximate distance
between
